How to compare two bikes
Start with the bike you know best. Enter its frame stack and reach in Bike A, then add the figures for a new frame size, a second bike or a proposed custom geometry in Bike B. The drawing aligns both bikes at the centre of the bottom bracket and uses the same scale. The difference column subtracts A from B. If Bike B has 25 mm more stack and 10 mm less reach, its head tube reference point sits 25 mm higher and 10 mm closer to the bottom bracket horizontally.
What stack and reach measure
Frame stack is the vertical distance from the bottom bracket centre to the centre of the top of the head tube. Frame reach is the horizontal distance between those same points. These dimensions let you compare sizes even when manufacturers use different size names. The reference point is on the frame. A headset cover, spacers, stem and handlebar all influence the final hand position on a built bicycle.
Compare saddle and hand positions
For a fit comparison, use a consistent reference point on both saddles and one spot on the bars where you actually grip, such as the top of the brake hoods. Set the bike upright on a level surface. Use a level and plumb line to measure the vertical and horizontal differences from the bottom bracket centre. Enter saddle setback as a positive distance when the saddle reference point is behind the bottom bracket. Saddle Y is a vertical measurement. A diagonal tape measurement along the seat tube will give a different result. For the hand point, enter both the distance forwards and the height above the same centre.
Use the zoom to compare the points closely. The horizontal saddle-to-hand measurement describes how far the grip lies ahead of the saddle. Saddle-to-hand drop measures how far the grip lies below it. A negative drop places the grip above the saddle. A different bar shape or brake hood installation can move the point even when the stem and frame stay the same. Compare equivalent gripping surfaces, especially when transferring your position from a road bike to a gravel bike.
Read the wheel and frame outline
Add head angle and head tube length to show the steering axis segment. The seat angle draws a schematic seat tube, whose illustrated length is approximate. Chainstay length and bottom bracket drop locate the rear axle. Wheelbase then locates the front axle on the same horizontal line. Enter the effective outside tyre radius to show both wheels. This view assumes equal front and rear radii on each bike. Use the actual outside measurement rather than half the nominal wheel size. Tube outlines are schematic and do not show clearance, fork offset or suspension sag.
Import geometry from BikeCAD or a table
In BikeCAD Pro, configure the columns for the CSV export and include Stack and Reach. Load the CSV or paste the relevant cells with their column headers from a spreadsheet. Select a record and apply it to either bike. Heading names such as Head angle, Chain stay length, Wheelbase and BB drop can fill additional fields. Check the values after import and enter any missing contact points manually. A dimensions table usually describes the frame, while a contact point depends on the assembled bike. Bicycles with matching frame coordinates can still fit differently once built.
In BikeGeoCalc, open Export | Import and copy the JSON text. Paste it into the import field here. The saddle reference is the centre defined in BikeGeoCalc, and the hand reference is the top of the brake hood. Use those same reference points when measuring a second bike by hand.
Why the fork matters in a 29 vs 32 inch comparison
Start by distinguishing two questions. If you know the finished geometry of two different bikes, align them at their bottom brackets and compare the saddle and hand points relative to the cranks. If you want to understand what a different fork and wheels would do to one frame, use the simulator above. It keeps Bike A’s frame and its saddle and cockpit settings fixed, then rotates each proposed build until both tyres reach the same ground line. Aligning the rear contact patches makes it easier to see what happens at the front wheel and how high the cockpit sits relative to the floor.
The example uses the 395 mm axle-to-crown and 47 mm offset of an ENVE Gravel Disc Fork, and the 495 mm axle-to-crown and 44 mm offset specified for the Esker Lorax 32. That is a 100 mm difference between these two examples. The Esker is designed around its 32-inch wheels and fork. The overlay isolates the effect of those dimensions on one reference frame. The example radii are illustrative. Measure from the axle to the outside of your inflated tyre for your own comparison. Changing both radii equally raises the whole bike by the same amount if the fork stays the same. A different front-to-rear radius difference changes the frame angle as well.
Axle-to-crown, offset and trail
Axle-to-crown is the straight-line distance between the front axle centre and the crown race seat on the steering axis. Check the drawing for the definition used by your fork manufacturer. In the model, offset is the perpendicular distance from that axis to the axle. Trail is measured along the ground from the tyre contact point forward to where the steering axis meets the ground. At the same head angle and offset, a larger front tyre radius increases geometric trail. At the same radius and angle, more fork offset reduces it. A longer fork raises the front of the same frame, typically slackening the head angle and increasing trail. The result also depends on the two tyre radii and the new offset.
Read the bottom bracket height and hand height alongside stack and reach. If the bars rise without any spacer change, the entire frame may have tilted. The simulator models rigid components, round tyres and level ground. It places the crown race seat at the lower head tube reference and approximates the tube outlines. Clearances, headset stack, suspension sag, axle and brake standards, toe overlap and frame approval have to be checked separately before building or riding a conversion.
Use your current bike as a reference for a custom build
Record the setup you can ride comfortably for several hours and use it as Bike A. Then enter the changes you want to try in Bike B. Compare the saddle and hand points first if you want to transfer your position. Review the frame and wheel dimensions when discussing the handling and intended use of the new bike. For a custom titanium frame or a fitting consultation, bring your current settings and the differences you want to discuss to HILITE Bikes in Basel.
